Mettler Toledo M400/2(X)H Especificaciones descargar pdf (Pagina 11)

Transmitter M400/2(X)H, M400G/2XH 11

Printed in Switzerland 30 031 683

NOTE: PROCESS UPSETS

Because process and safety conditions may depend on consistent operation of this trans-

mitter, provide appropriate means to maintain operation during sensor cleaning, replace-

ment or sensor or instrument calibration.

NOTE: This is a 2-wire-product with two active 4–20 mA analog output.

2.2 Correct disposal of the unit

When the transmitter is finally removed from service, observe all local environmental regulations

for proper disposal.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 110 111

Operation Manual 1
Multi-parameter 1
1 Introduction 9
2 Safety instructions 10
3 Unit overview 14
3.2.1 Menu Structure 15
3.2.2 Navigation keys 15
3.2.6 ”Save changes” dialog 17
3.2.7 Security Passwords 17
3.2.8 Display 17
4 Installation instruction 18
4.1.2 Installation procedure 19
(+ 0,5 mm/– 0,0 mm) 20
(+ 0.02"/– 0.00") 20
4.2.1 Housing (wall mount) 21
4.3 Connector PIN denition 22
4.3.3 Analog Sensors 23
InPro 3250i/SG/120 25
Art.-Nr. 52 005 373 25
4.5.2.1 Example 1 27
4.5.2.2 Example 2 28
4.5.2.3 Example 3 29
4.5.2.4 Example 4 30
6 Quick Setup 34
7 Sensor Calibration 35
(four electrode sensors only) 37
7.2.3 Process Calibration 38
7.3.1.1 Auto mode 39
7.3.1.2 Manual mode 40
7.4 pH calibration 41
7.4.1 One point calibration 41
7.4.1.1 Auto mode 41
7.4.1.2 Manual Mode 42
7.4.2 Two-point calibration 42
7.4.2.1 Auto Mode 42
7.4.2.2 Manual Mode 43
7.4.3 Process calibration 44
(only for analog sensors) 46
(only for analog sensor) 47
7.7 Sensor verication 47
8 Conguration 48
8.2.1.1 Analog sensor 49
8.2.1.2 ISM sensor 49
8.2.3.2 Concentration table 52
8.2.3.3 pH / ORP parameters 53
 or . key 54
8.2.4 Set averaging 55
8.3 Analog outputs 56
8.4 Set points 57
8.5 Alarm / Clean 58
8.5.1 Alarm 58
8.5.2 Clean 59
8.6 ISM set up 60
8.6.1 Sensor monitoring 60
8.6.2 CIP Cycle Limit 61
8.6.3 SIP Cycle Limit 62
 and . keys and press 63
8.7 Display 64
8.7.1 Measurement 64
8.7.2 Resolution 65
8.7.3 Backlight 65
8.7.4 Name 65
8.8 Hold analog outputs 66
9 System 67
9.2.1 Changing passwords 68
9.3 Set / Clear lockout 68
9.4 Reset 68
9.4.1 Reset system 69
9.5 Set date & time 69
10 PID setup 70
10.1 Enter PID setup 71
10.2 PID auto / manual 71
10.3 Mode 71
10.3.1 PID mode 72
10.4 Tune parameters 73
10.4.3 Proportional limits 73
10.4.4 Corner points 73
10.5 PID display 74
11 Service 75
11.1.3 Display 76
11.1.4 Keypad 76
11.1.5 Memory 76
11.1.6 Set OC 76
11.1.7 Read OC 77
11.1.8 Set analog outputs 77
11.1.9 Read analog outputs 77
11.2 Calibrate 77
11.2.1.1 Temperature 78
11.2.1.2 Current 78
11.2.1.3 Voltage 79
11.2.1.4 Rg diagnostic 79
11.2.1.5 Rr diagnostic 80
11.2.2 Calibrate unlock 81
11.3 Tech Service 81
12 Info 82
12.4 ISM sensor info 83
13 Maintenance 86
14 Troubleshooting 87
14.3.3 ORP messages 89
14.4 Amperometric O 90
Error messages / 90
Warning- and Alarm list 90
14.4.3 Trace oxygen sensors 91
14.5.1 Warning indication 92
14.5.2 Alarm indication 92
16 Specications 94
17 Default table 99
Resistivity/Conductivity 103
18 Warranty 104
19 Buffer tables 105
19.1.2 Mettler-10 106
19.1.5 Hach buffers 107
19.1.6 Ciba (94) buffers 108
19.1.8 WTW buffers 109
19.1.9 JIS Z 8802 buffers 109

Comentarios a estos manuales

Sin comentarios

Mettler Toledo M400/2(X)H Especificaciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control Mettler Toledo M400/2(X)H