Mettler Toledo M300 FLOW Especificaciones Pagina 21
- Pagina / 70
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transmitter M300 FLOW 21
© 09 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M300 FLOW
Printed in Switzerland 52 121 319
4.4 Connection of Sensor
The M300 FLOW Transmitter is designed to operate with various types of sensors. These
sensors require different wiring configurations. Listed below are instructions for wiring the
various types of sensors offered by Mettler-Toledo Thornton for use with this transmitter. Please
consult the factory for assistance if attempting to wire sensors not offered by Mettler-Toledo
Thornton as some sensors may not be compatible.
4.5 Flow Sensor Input Wiring Kit
This kit contains components that may be needed at input terminals to condition sensor signals.
Refer to the following sections or to the instruction manual for wiring details.
4.6 Kit Contents
This kit contains the following items:
− 4x Wire nuts
− 4x 10K ohm resistors for use with Burket 8020 and 8030 type sensors, and GF Signet
2500-series sensors.
− 4x 1K ohm resistors for use with Data Industrial 200-series and Fluidyne insertion type
sensors.
− 4x 0.33uF, 50 V capacitors for use with Berket 8020 and 8030 type sensors, Data
Industrial 200-series and 4000-series sensors, GF Signet 2500-series sensors, Sanitary
Turbine-Type sensors, Fluidyne insertion type sensors and Racine Federated (Formerly Asahi/
America) vortex-style sensors.
4.7 Flow sensor wiring for Compatible Sensors
The following sections provide wiring information to properly connect various compatible flow
sensors to the M300 FLOW Transmitter. When using the Configuration menu of the transmitter to
setup the flow sensor, the first prompt asks to select the TYPE of flow sensor being connected.
There are three choices as follows:
High: All flow sensors described in Section 4.5.1
Low: P515 Signet flow sensors only, described in section 4.5.2
Type 2: Asahi flow sensors, described in Section 4.5.3
- Operation Manual 1
- Transmitter M300 FLOW 1
- Transmitter M300 FLOW 2 2
- Transmitter M300 FLOW 4 4
- Transmitter M300 FLOW 5 5
- Transmitter M300 FLOW 6 6
- 1 Introduction 7
- 2 Safety instructions 7
- Transmitter M300 FLOW 8 8
- 3 Unit overview 9
- 3.2 Overview 1/2DIN 10
- 3.3 Control/Navigation Keys 11
- 3.3.2 Navigation keys 12
- 3.4 Display 13
- 4 Installation instruction 14
- Power Fuse 15
- METTLER TOLEDO 17
- 4.3 Connector PIN definition 19
- Transmitter M300 FLOW 20 20
- 4.4 Connection of Sensor 21
- 4.6 Kit Contents 21
- Flow Sensors 22
- Type: high 22
- Racine Federated 26
- (formerly Asahi/America) 26
- Vortex Sensor 26
- 5 Placing in/out of service 27
- 6 Quick Setup 28
- 6.4 Measurement Selection 29
- 6.5 Analog Outputs 29
- 6.6 Set Points 30
- 7 Calibration 31
- 7.2 Sensor Calibration 32
- 7.2.2 Two point Calibration 33
- 7.3 Edit 34
- 7.4 Verify 34
- 8 Configuration 35
- 8.2 Measurement Setup 36
- 8.2.1 Set Averaging 37
- 8.2.2 Set Pipe ID 37
- 8.2.3 Reset Total Flow 38
- 8.2.4 External Total Reset 38
- 8.3 Analog Outputs 39
- 8.4 Set Points 40
- Transmitter M300 FLOW 41 41
- 8.5 Alarm 42
- 8.6 Display 43
- 8.6.3 Backlight 44
- 8.6.4 Name 44
- 8.7 Hold Outputs 45
- 9 System 46
- 9.3 Passwords 47
- 9.4 Set/Clear Lockout 48
- 9.5 Reset 48
- Transmitter M300 FLOW 49 49
- 10 PID Setup 50
- 10.1 Enter PID Setup 51
- 10.2 PID Display Auto-Manual 51
- 10.3 Tune Parameters 51
- 10.3.3 Proportional Limits 52
- 10.3.4 Corner Points 52
- 10.4 Mode 53
- 10.4.2 PID Control Tuning 54
- 11 Service 55
- 11.1.2 Digital Input 56
- 11.1.3 Display 56
- 11.1.4 Keypad 56
- 11.1.5 Memory 56
- 11.1.6 Set Relays 57
- 11.1.7 Read Relays 57
- 11.1.8 Set Analog Outputs 57
- 11.2 Calibrate 58
- 11.2.2 Calibrate Analog 59
- 11.3 Tech Service 60
- 12 Info 61
- 13 Maintenance 62
- 14 Trouble Shooting 63
- 16 Specifications 64
- Transmitter M300 FLOW 65 65
- 17 Default Tables 66
- Transmitter M300 FLOW 67 67
- 18 Warranty 68
- 19 UL Statement 68
- Transmitter M300 FLOW 69 69
Relacionado con productos y manuales para De medición, control y control Mettler Toledo M300 FLOW
(12 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales